This item has been SOLD
2013 Vianord EVO 2.1 Plate Making System – 090723265002A
It is an all-in-one unit in the size 66 x 86 cm (26″ x 34″).
It is the first unit of its kind and size which is also equipped with a separate pre-wash section for digital plates with black (LAMS) layer running like a flowline (prewash/wash/cleaning/wiping).
Encumbrance
The minimum distance from the walls to your system should be of 1.2 mt (47.2”) in front, 0.5 mt (19.7”) at the rear and on the left-hand side and 0.65 mt (25. 6”) on the right-hand side.
The respect of the minimum distance from the walls is critical to allow sufficient space to the users and the engineers to be able to have access to the system in case of maintenance and repairs.
CE Certification
The equipment is designed and manufactured according to the EEC safety and health standards and on the basis of the verifications carried out according to the essential requirements of the Directive 2006/42/EC, the system respects and is in compliance with all the applicable points.
General Features
This automatic, PLC controlled, EVO system is specifically designed for high quality digital and conventional photopolymer plates for small printing applications (e.g. narrow web).
Solvent
It is designed to work in a standard “drum-to-drum” configuration where fresh solvent is supplied to the washout unit from a drum and the saturated dirty solvent is pumped from the unit to a recovery drum. It has been tested with conventional solvents, with flashpoint above 62°C (144°F). The system’s installation kit includes two Ø 16 mm – 5 mt solvent hoses with fittings, one level switch for the fresh solvent drum and another for the used solvent drum. Please note that if you intend to use your this system with permanently installed tanks, special level switches may be required.
Exposure
– High concentration UV-A radiations
– Lamps temperature management
– Controlled airstream for lamps cooling
– Exposure bed temperature management
– Water cooled exposure bed
– Light integrator for compensation of UVA aging lamps
– Vacuum system for analogue plates
Processor
Dryer
– Drawers Pre-Heating management
– Temperature management system
– Separate Heat management (one each 2 drawers)
– Dedicated exhaust system
Light Finisher
– Flexible post exposure and light finishing sequence
– Static cooling system (air cooling)
Production Data Recording
Stress-Accumulation Early-Warning
Remote Diagnostics
System Dimensions (net)
250 x 173 x 114 cm
(98.43 x 68.11 x 44.88”)
System Weight (net)
Mains Electricity
Power Supply (field configurable)
360 / 440 Volt – 50 / 60 Hz – 3Ph / N / PE – 207 / 243 Volt – 50 / 60 Hz – 3Ph / PE
Current (nominal load)
16 A (360/440 Volt configuration) – 28 A (207/243 Volt configuration)
Power Rating (nominal)
10 Kw
Connecting Wires
5 x 4 mm2 (360/440 Volt configuration) – 4 x 6 mm2 (207/243 Volt configuration)
Grounding
Compressed Air Supply
To perform to the best of its possibilities, the system requires a continuous and stable supply of compressed air at a pressure of at least 7 bar (101.5 psi) and not more than 10 bar (145 psi), with pressure dew point 3°C and max. residual intake oil content of < 0.01 mg/m3. Consider also an average consumption of 70 l/hr. The system installation kit includes a 5-meter – Ø 6mm air connecting pipe for push-in fitting.
Exhaust
The unit is equipped with a well-designed exhaust system that collect and conveys vapours and fumes from the different sections the machine and discharge them as quickly and silently as possible. The blower in the systems has sufficient power to vent the entire equipment when the tube supplied is connected directly to a vent hoods in the external wall or on the roof.
Washout/Dryer
Duct connection: Ø 100 mm (3.94”) Airflow: 200-350 m3/h
Light-Finisher
Duct connection: Ø 100 mm (3.94”) Airflow: 200-350 m3/h
Working Environment
The system should be installed in a clean, constant-temperature and constant-humidity pre-printing environment with a temperature between 18 and 26°C (64.4 and 78.8°F) and a non-condensing relative humidity in the range of 40 to 60%.
To maintain such environmental standards an efficient heating/cooling and ventilating system may be required.
System Colour
Vianord offers all equipment in standard powder coating Vianord Black.
In addition, Vianord offers numerous ways you can personalize your system. In fact, Vianord offers the best customization options in the industry! This allows you to showcase your brand and company’s spirit in ways other companies can’t offer. You can choose your personal colour and have your logo, company name, or slogan pop.
Click This Button To View The Lot
On Auction Now!
